OG shop member gallery
OldGobbler
          bullet Forum Board      bullet Pushpin Turkey Call Blog      bullet Advertising Info     

OG Gear Store

Sum Toy
Dave Smith
Wood Haven
North Mountain Gear
North Mountain Gear
DC Cattle Ranch






Author Topic: Making the cuts  (Read 457 times)

Offline MRS

  • Jr. Member
  • *
  • Posts: 5
Making the cuts
« on: June 30, 2021, 07:55:31 PM »
Anyone know of or would be willing to make a step by step video on
How to make the cuts of the batwing cut.

Offline GobbleNut

  • Limbhanger
  • ******
  • Posts: 4237
  • Southern New Mexico
Re: Making the cuts
« Reply #1 on: July 02, 2021, 09:51:19 AM »
Sounds like another project for Ben (compton30) to pursue! 

...Simply stated, the batwing is basically just a center V-cut with the side tabs either cut off or pulled off.  That is pretty obvious, so I am guessing that your question relates to how you hold the call with one hand and cut with the other?  That can be done, but it takes some dexterity.  I don't make many batwings, but if I did, I think I would devise some sort of small vice-like dealybob to hold the call so I could cut the tabs with one hand while holding them with the other. 

As it is, when I decide to make a batwing, I just pop the tabs off by just grabbing them and yanking them off.  Granted, that is not the most precise method of accomplishing the task, but it will work in a pinch.   :D ;D

Offline MRS

  • Jr. Member
  • *
  • Posts: 5
Re: Making the cuts
« Reply #2 on: July 03, 2021, 08:23:32 AM »
 Big fingers are getting in the way to make a nice cut line like production calls
I did reverse my cut direction and that seemed to help.


A clamp or small vise like a  fellow mentioned on another post might be the solution for me too

Offline SCGobbler

  • 2020 SITE SUPPORTER
  • Hero Member
  • ********
  • Posts: 481
  • Ya can't fix stupid!
Re: Making the cuts
« Reply #3 on: July 04, 2021, 11:47:02 PM »
I started using a small clamp from harbor freight to clamp the call to the edge of my table. The problem is the figuring out how you are going to cut the tabs off when the tVle gets in the way of your scissors.


Sent from Gobbler’s Branch on the go!
The SC Gobbler




Some men are mere hunters; others are turkey hunters.
                    —Archibald Rutledge

Offline MRS

  • Jr. Member
  • *
  • Posts: 5
Re: Making the cuts
« Reply #4 on: July 05, 2021, 04:56:06 PM »
I have gotten alot better by not making any cuts till after I apply tape to the call, this gives me more material to hold onto.


Offline compton30

  • The Boss Gobbler
  • ****
  • Posts: 602
Re: Making the cuts
« Reply #5 on: July 09, 2021, 12:30:51 PM »
Sounds like another project for Ben (compton30) to pursue! 

...Simply stated, the batwing is basically just a center V-cut with the side tabs either cut off or pulled off.  That is pretty obvious, so I am guessing that your question relates to how you hold the call with one hand and cut with the other?  That can be done, but it takes some dexterity.  I don't make many batwings, but if I did, I think I would devise some sort of small vice-like dealybob to hold the call so I could cut the tabs with one hand while holding them with the other. 

As it is, when I decide to make a batwing, I just pop the tabs off by just grabbing them and yanking them off.  Granted, that is not the most precise method of accomplishing the task, but it will work in a pinch.   :D ;D

Coming up!