Hey guys. I was given a remington 1100 from the 60's that belonged to my great grandfather. I don't believe that it has ever been cleaned because it is filthy! In the process of taking it down to clean I found the barrel is stuck and won't budge. I have trying wd-40 where the barrel and receiver mate but no luck. Any help would be greatly appreciated.
Sent from my iPhone using Tapatalk
Pull the trigger group and soak the heck out of it inside and out with the WD. Let it sit a day or two then try again.
I'd take the butt stock and fore stock off first so you don't soak them with oil.
QuoteQuoteI'd take the butt stock and fore stock off first so you don't soak them with oil.
Good advice already. Is it just dirty or can you also see rust? Those are fine old guns but it may well have some rust that is binding the barrel to the receiver. The WD 40 will probably work, if not Kroil might help. I'd put it muzzle down in the warmest spot you have and be patient.
You may also want to call John Mann @ Mann & Son Sporting Goods (Since 1945) @ 618.357.2911, ask for John or Dustin, tell them what's happening and they can probably give you good advice on how to solve the problem. Patience is normally the key however.
Thanks,
Clark
Break-Free may work as well. I always for get about Kroil, so good call on that one!
Balistol might work and it was designed not to harm the wood. YouTube "hicock45 Ballistol" and watch a couple of his YouTubes before you use it. I have been using it on all of my guns as a CLP and love it.
Thanks guys. I believe the gun is just dirty. I don't see any visible rust. It has been soaking in WD for 24 hours and I'm going to let it go another 24 and try again.
Sent from my iPhone using Tapatalk
PB Blaster will break rust when nothing else will.
http://www.top-downsolutions.com/pb-blaster
I would've suggested Kroil but not everybody has it laying around. I have to order it as no one carries it in my area. Kerosene works great for loosening stubborn parts and that's basically what WD 40 is. Since you already have it mightswell give it some time to work. It'll probably do the job. Basically the years of oil and grime turn into sticky gunk and that's likely what's holding you up. Pulling the wood off is definitely a good idea.
You can also use a propane torch, but have to take it easy and don't apply to much heat, just warm the top of the receiver where the barrel goes in. That will loses up the crud, and keep spraying WD, or PB Blaster on it while you heat it. The heat will draw the oil in there, a heatgun or a hair dryer will work also, but if you use the torch just take it easy and keep the flame moving around on the metal and don't get it to hot. Another thing the barrel may have crud built up were it goes around the mag tube!
Remember that many products that will cut through rust and gunk are also flamable, some very flamable.
Use of open flames around most of these is discouraged. Please read the cautions on containers and be very careful.
Patience is a key in a project like this.
Thanks,
Clark
If the WD-40 doesn't work, I would try kroll. I have used it a lot on froze up bolts, with very good results.
Quote from: TJR on January 21, 2015, 10:53:58 AM
Thanks guys. I believe the gun is just dirty. I don't see any visible rust. It has been soaking in WD for 24 hours and I'm going to let it go another 24 and try again.
Sent from my iPhone using Tapatalk
Did you get this yet?? I'd be shocked if PB Blaster doesn't work.
Still soaking in WD. I'm going to give it another shot this evening and if it won't break loose I'm going to give another product a try. I'll keep you guys posted. Thanks again for all the tips.
Sent from my iPhone using Tapatalk
Quote from: TJR on January 22, 2015, 06:10:59 PM
Still soaking in WD. I'm going to give it another shot this evening and if it won't break loose I'm going to give another product a try. I'll keep you guys posted. Thanks again for all the tips.
Sent from my iPhone using Tapatalk
If you have a couple of those rubber circles that are used to help loosen jar lids or something like like, that rubber shelf liner works well, it will allow you get a grip on the barrel and on the receiver. A little manipulation and then more soaking may be necessary. Patience in a real key.
Thanks,
Clark
I sure hope this turns out better than the fella with the stuck choke awhile back. Good luck and take your time.
Quote from: allaboutshooting on January 22, 2015, 06:18:33 PM
Quote from: TJR on January 22, 2015, 06:10:59 PM
Still soaking in WD. I'm going to give it another shot this evening and if it won't break loose I'm going to give another product a try. I'll keep you guys posted. Thanks again for all the tips.
Sent from my iPhone using Tapatalk
If you have a couple of those rubber circles that are used to help loosen jar lids or something like like, that rubber shelf liner works well, it will allow you get a grip on the barrel and on the receiver. A little manipulation and then more soaking may be necessary. Patience in a real key.
Thanks,
Clark
You stole my thunder, Clark. The rubber grippers really help. Just be sure you have the grip on the receiver and not the stock, or you could break the stock.
Quote from: silvestris on January 22, 2015, 07:00:38 PM
Quote from: allaboutshooting on January 22, 2015, 06:18:33 PM
Quote from: TJR on January 22, 2015, 06:10:59 PM
Still soaking in WD. I'm going to give it another shot this evening and if it won't break loose I'm going to give another product a try. I'll keep you guys posted. Thanks again for all the tips.
Sent from my iPhone using Tapatalk
If you have a couple of those rubber circles that are used to help loosen jar lids or something like like, that rubber shelf liner works well, it will allow you get a grip on the barrel and on the receiver. A little manipulation and then more soaking may be necessary. Patience in a real key.
Thanks,
Clark
You stole my thunder, Clark. The rubber grippers really help. Just be sure you have the grip on the receiver and not the stock, or you could break the stock.
How about now? Get it?
Still stuck! I've exhausted most of my options. I may have to take it to a gunsmith and see if they will have any success. I'm going to keep trying for a while longer. Thank you all for the help I will keep you posted if I have any luck.
Sent from my iPhone using Tapatalk
I agree with Clark..Kroil and Patience..Kroil and Patience...Soak it and let it work a few weeks, then soak again..that Kroil will creep in there and eventually loosen things up.
Just don't put it in vice. Do the Kroil as recommended above.
I've always wondered if ultrasound cleaning could break loose these rusty parts
Get two rubber grippers and a friend. One of you grips the barrel and the other grips the RECEIVER and both pull with all you've got. Do this outside as when it breaks free you both will probably end up on your derrières.