As a follow up to the last couple of comments in the Hevi Shot discussion down below, is it really that expensive to initially get setup to handload one's own TSS? What would a person expect to spend with the below list and anything else needed that I have missed to get started?
I am not expert, so please be merciful if I have missed some needed items, but beyond some type of hull trimmer (or a shell vise to improvise with a home made measurement with something like PVC), a dependable digital scale, a few spoons, a shell block, a dental dam, a drill press or a hand crank roll crimper, the actual crimper bit itself, - beyond that what else is needed to load besides the obvious stuff like shot, hulls (with primers), shotwad (some need mylar), felt/wax cushion, overshot card, etc.?
What have I missed that is not in the above list?
Am I correct to think that a person is saving 3.50-5.00 per load to load their own TSS once beyond the initial investment to get started? (It will take a while to get that investment back no doubt, and I would load some for other hunters/friends for at least long enough to get back to break even on initial equipment cost - my buddies are begging me to do this).
It's probably cheaper to buy TSS shells rather than reload it yourself when you take everything into consideration. I think my patterns are close to the same as what is available commercially.
I like rolling my own but it takes time and equipment. Shipping, taxes, buying components in bulk, etc gets expensive. Plus once your friends find out they will want shells also.
You can get away with a roll crimper, scale, and hand drill and make some shells.
If I found out about TSS today, I would just buy as many 20 gauge Foxtrot shells as I could afford. I like their shells because they are fold crimped. I would just stock up in the off season when you can get what you want.
Sent from my iPhone using Tapatalk
So this is a multi tiered question. First of all, I don't roll crimp. It sounds like you have all your tools/equipment. It depends on the load you choose to load. Example: I load 28 gauge 1.5 oz #9 TSS. The cost is @ $340 plus shipping. for 53 shells. It looks like $6-$7 per round. If you have some of this material or buy in a bigger bulk, you will save a little bit. These are ballpark numbers that I got off the Precision Reloading Site, Ballistic Products are about the same prics too. Z
5 pounds of shot is @ $225
100 wads are @ $15
100 primed new hulls @ $25
lg can of buffer @ $15
250 felt spacers @ $12
100 mylar @ $8
1 pound Lil Gun powder @ $40
It's somewhat pricey to get started but get piece by piece. Once you get enough supplies on hand you'll not be without.
Throughout all the Obama nonsense of making things tough I shot all sorts of guns planet as I had everything.
Than there's the "coolness" factor in a sense of doing it yourself whether it was lead, tss or metallic cartridges. If you like that sort thing it'll add to your sport.
Understand TSS loading is not reloading in a sense it's more of putting parts together. Reloading involves lots of testing, changing, massaging loads. TSS loads are often high pressure loads. Can't mess with them too much
Quote from: Bowguy on February 13, 2025, 01:40:57 PMIt's somewhat pricey to get started but get piece by piece. Once you get enough supplies on hand you'll not be without.
Throughout all the Obama nonsense of making things tough I shot all sorts of guns planet as I had everything.
Than there's the "coolness" factor in a sense of doing it yourself whether it was lead, tss or metallic cartridges. If you like that sort thing it'll add to your sport.
Understand TSS loading is not reloading in a sense it's more of putting parts together. Reloading involves lots of testing, changing, massaging loads. TSS loads are often high pressure loads. Can't mess with them too much
Don't overlook the coolness factor. When you break out some shells at Turkey camp and somebody says "where did you buy those" it is fun.
Sent from my iPhone using Tapatalk
Not trying to high jack this thread but add to it. This just popped into my pea brain. I already have a Mec 600 Jr for 12 and 20's, that I use to reload dove loads, plenty of 12 and 20 gauge 2 3/4-inch shells, would TSS be easy peasy for the MEC's? You guys are always talking about using card stock and roll crimping them, so the DUH light just came on. I normally use the 8-point crimp.
It's cheaper to load your own if you don't buy a loading press.
I roll crimp with my cordless and an adapter to make it a press, I had one a neighbor gave me but they are cheap.
Components are cheap, powder is cheap in the long run but initially it's not. Can load hundreds of shells with a can of powder.
Hulls, wads and fillers come between 100 and 250 at a crack so they last a long time!
I like loading them, I know what I'm getting and once choke and gun are dialed your good!
If you only shoot a couple rounds a year I would just buy it!
I started out before you could buy loaded shells so I just kept at it.
Sent from my iPhone using Tapatalk
Can definitely use your mec, and maybe some of the same hulls and powder you already have.
Just ask a supplier if he has any loads that use some of your components!
Sent from my iPhone using Tapatalk
Quote from: Dtrkyman on February 13, 2025, 02:11:14 PMCan definitely use your mec, and maybe some of the same hulls and powder you already have.
Just ask a supplier if he has any loads that use some of your components!
Sent from my iPhone using Tapatalk
Thanks! Good to know. All I would need is a recipe, add primers, powder, wads and the TSS. Got me thinking now.
I crimp with a MEC and it works fine. IF you follow a trusted recipe then there should be no issues. Z
Quote from: bbcoach on February 13, 2025, 02:04:03 PMNot trying to high jack this thread but add to it. This just popped into my pea brain. I already have a Mec 600 Jr for 12 and 20's, that I use to reload dove loads, plenty of 12 and 20 gauge 2 3/4-inch shells, would TSS be easy peasy for the MEC's? You guys are always talking about using card stock and roll crimping them, so the DUH light just came on. I normally use the 8-point crimp.
Quote from: Alabama556 on February 13, 2025, 01:45:49 PMQuote from: Bowguy on February 13, 2025, 01:40:57 PMIt's somewhat pricey to get started but get piece by piece. Once you get enough supplies on hand you'll not be without.
Throughout all the Obama nonsense of making things tough I shot all sorts of guns planet as I had everything.
Than there's the "coolness" factor in a sense of doing it yourself whether it was lead, tss or metallic cartridges. If you like that sort thing it'll add to your sport.
Understand TSS loading is not reloading in a sense it's more of putting parts together. Reloading involves lots of testing, changing, massaging loads. TSS loads are often high pressure loads. Can't mess with them too much
Don't overlook the coolness factor. When you break out some shells at Turkey camp and somebody says "where did you buy those" it is fun.
Sent from my iPhone using Tapatalk
I do all I can myself that's why I mentioned it. Load my shells, brass, make arrows, including standing, finishing them including cutting full length feathers and splicing the feathers to make neat combos. Mouth calls, Tie my flies, make bowstrings, used to cast black power projectiles, etc etc etc.
Just keeps us more in touch with our lifestyle.
Quote from: zelmo1 on February 13, 2025, 01:35:37 PMSo this is a multi tiered question. First of all, I don't roll crimp. It sounds like you have all your tools/equipment. It depends on the load you choose to load. Example: I load 28 gauge 1.5 oz #9 TSS. The cost is @ $340 plus shipping. for 53 shells. It looks like $6-$7 per round. If you have some of this material or buy in a bigger bulk, you will save a little bit. These are ballpark numbers that I got off the Precision Reloading Site, Ballistic Products are about the same prics too. Z
5 pounds of shot is @ $225
100 wads are @ $15
100 primed new hulls @ $25
lg can of buffer @ $15
250 felt spacers @ $12
100 mylar @ $8
1 pound Lil Gun powder @ $40
I was guessing that one could save 3.5-5 dollar per load doing it themselves, and if it is coming in at around 7 dollar in materials give or take, that was close. Your response was very helpful - Thank you Zelmo.
Quote from: Bowguy
Sent from my iPhone using Tapatalk
/quote]
I do all I can myself that's why I mentioned it. Load my shells, brass, make arrows, including standing, finishing them including cutting full length feathers and splicing the feathers to make neat combos. Mouth calls, Tie my flies, make bowstrings, used to cast black power projectiles, etc etc etc.
Just keeps us more in touch with our lifestyle.
That is why we need to be living next door to you Mike. You are a cut above the rest. Glad you are doing really good again. Wish we were closer to each other, I could learn something from you.
Thanks to EVERYONE who replied - all replies helped me to get a better grasp on going down this road. I may reach out to some of you by way of phone (I have the phone number for a few of you) or private message and ask a few follow up questions if that is ok. Thanks again!
Quote from: zelmo1 on February 13, 2025, 01:35:37 PMSo this is a multi tiered question. First of all, I don't roll crimp. It sounds like you have all your tools/equipment. It depends on the load you choose to load. Example: I load 28 gauge 1.5 oz #9 TSS. The cost is @ $340 plus shipping. for 53 shells. It looks like $6-$7 per round. If you have some of this material or buy in a bigger bulk, you will save a little bit. These are ballpark numbers that I got off the Precision Reloading Site, Ballistic Products are about the same prics too. Z
5 pounds of shot is @ $225
100 wads are @ $15
100 primed new hulls @ $25
lg can of buffer @ $15
250 felt spacers @ $12
100 mylar @ $8
1 pound Lil Gun powder @ $40
Great post. Back when I was a kid, we loaded all our lead shells... Target, upland, waterfowl, etc... Much cheaper to purchase in bulk, and my father's friends would get together every couple years and make a bulk purchase... Loading shells was half or less the cost of factory, and we get better loads... Currently with non-tox loads, I do not see the savings, especially when you factor in time.
I do have to ask (for all the TSS loaders), why not load 2 3/4" shells, and not use spacers? I would think cheaper and less time consuming???
The prices on here are accurate. I roll crimp on a drill press. Really the crimp, shot and powder are major cost. You do save some cash on each shell, but I enjoy doing it and can continue to make shells ever if production stops from major companies.
Sent from my iPhone using Tapatalk
My loads are 2 3/4". The felt is to take up space in the wad because of the drastic weight difference between lead and TSS. If you used the same volume the TSS would be @ 50% heavier. Z
Quote from: mountainhunter1 on February 13, 2025, 07:27:25 PMQuote from: Bowguy
Sent from my iPhone using Tapatalk
/quote]
I do all I can myself that's why I mentioned it. Load my shells, brass, make arrows, including standing, finishing them including cutting full length feathers and splicing the feathers to make neat combos. Mouth calls, Tie my flies, make bowstrings, used to cast black power projectiles, etc etc etc.
Just keeps us more in touch with our lifestyle.
That is why we need to be living next door to you Mike. You are a cut above the rest. Glad you are doing really good again. Wish we were closer to each other, I could learn something from you.
Thanks to EVERYONE who replied - all replies helped me to get a better grasp on going down this road. I may reach out to some of you by way of phone (I have the phone number for a few of you) or private message and ask a few follow up questions if that is ok. Thanks again!
Thank you for the kind words. Appreciated
Quote from: zelmo1 on February 14, 2025, 05:02:27 AMMy loads are 2 3/4". The felt is to take up space in the wad because of the drastic weight difference between lead and TSS. If you used the same volume the TSS would be @ 50% heavier. Z
This answered one of my questions on reloading TSS vs lead. Here's a couple more, Why the mylar wrap and why buffering?
Mylar is to protect the barrel from the tss shot. Tss is harder than lead.
The buffer is used with the smaller shot used for turkey hunting. I have been told it keeps the pellets from bouncing off each other in the barrel and then spinning out of the pattern after it leaves the barrel.
I have also have people tell me it helps fill up the cup in the wad.
I have shot my loads with and without buffer and have not seen a noticeable difference.
One of the biggest advantages of loading your own is not having your favorite store bought load discontinued or having the components changed in it.
Quote from: zelmo1 on February 14, 2025, 05:02:27 AMMy loads are 2 3/4". The felt is to take up space in the wad because of the drastic weight difference between lead and TSS. If you used the same volume the TSS would be @ 50% heavier. Z
I understand the TSS taking up less volume, and the need for a spacer... And as you are loading 2 3/4" shells, my question might not be applicable to you.
But I have seen on other posts and forums, where people are loading 3" shells with spacers... I do not understand the need for a 3" shell, and then putting in spacers? Also seems like a majority of factory sold TSS comes in 3" and my understanding is that there are spacers in these rounds as well??? My question is why load a 3" shell and then put in spacers? Why not load a 2 3/4" round and either use smaller or no spacer?
Hopefully reloading companies create a 2 3/4" wad designed for TSS loads, and we can do away with the spacers?
Feeling the difference between 1 1/8 oz load, and a 1 1/4 oz load, I know that those spacers will add payload to the recoil end of things, and increase felt recoil to some degree...
Probably has to do with wad availability. Most of the loads I have used use a steel shot wad and I don't think there are a bunch of 2 3/4 steel shot wads out there.
On my current 2 3/4 load I trim a 3 inch wad to fit a 2 3/4 hull.
On another note, if you ever change up a recipe like I mentioned above, please send your shells off to get pressure tested by precision reloading. You will be surprised what changing components can do to pressures.
That is just a guess on my part.
Sent from my iPhone using Tapatalk
Quote from: Alabama556 on February 14, 2025, 05:52:50 PMProbably has to do with wad availability. Most of the loads I have used use a steel shot wad and I don't think there are a bunch of 2 3/4 steel shot wads out there.
On my current 2 3/4 load I trim a 3 inch wad to fit a 2 3/4 hull.
On another note, if you ever change up a recipe like I mentioned above, please send your shells off to get pressure tested by precision reloading. You will be surprised what changing components can do to pressures.
That is just a guess on my part.
Posts from a different forum state that the spacers are used in longer hulls to reduce and control pressure.
That is true also.
Sent from my iPad using Tapatalk