Turkey hunting forum for turkey hunting tips

Turkey Calls => Mouth Call Making Discussion => Topic started by: DUCKDIGGLER on April 22, 2020, 04:31:43 PM

Title: Combo Cut advice needed....
Post by: DUCKDIGGLER on April 22, 2020, 04:31:43 PM
So guys....Im building my own and really dig a Combo cut.

2-Reed Top reed is .003 Green and bootom reed is .003 black side tensioned on FR Hand Jig to .170 with just a small smile of back tension.

I'm definetly a right side air guy and really can only get good front end with a combo cut. I can run a Ghost cut ok but can't get that good 2 note yelp with it.  So my question to you guys is are theyre any modifcations or otehr "right side" cuts I should try out? I usually trim the "stinger" on the left side of the call at a small angle , say 45 degrees. 

What say you guys?  Any other "recipes" I should try in a combo cut that will give me that clean front end?

Thank you all! DD :OGturkeyhead:
Title: Re: Combo Cut advice needed....
Post by: DUCKDIGGLER on April 26, 2020, 08:21:25 AM
Anyone? No recommendations at all?
Feel free to message me if you'd rather.

I'd appreciate any tips or suggestions you can offer.

Thank you. DD :funnyturkey:
Title: Re: Combo Cut advice needed....
Post by: Lonehowl on April 26, 2020, 01:51:10 PM
DD...I'm a reverse combo guy...left side air. I make that call and also same call but trim the tip on the top reed to an angle like you. Clearing away that trash lessons the rasp sometimes but helps to get a cleaner front note sometimes.
Edit to say...I prefer 0025 latex, not true proph, underneath. I like an easy blowing call and it works better for me than the black latex.
Title: Re: Combo Cut advice needed....
Post by: DUCKDIGGLER on April 26, 2020, 02:51:57 PM
Thank you sir! I will give that 25 latex a try this evening when I break the press out. I am really excited to kill a bird this year with a call I made myself. I wish I started building them years ago!

Much appreciated!
Title: Re: Combo Cut advice needed....
Post by: Lonehowl on April 26, 2020, 04:05:47 PM
Forgot to say...yellow top reed is what I like most. Blue is good too.
Title: Re: Combo Cut advice needed....
Post by: DUCKDIGGLER on April 26, 2020, 08:22:46 PM
Me likey!  I going to try a touch more side tension but I am digging it so far.

Thank you LH!
Title: Re: Combo Cut advice needed....
Post by: GobbleNut on April 28, 2020, 10:18:04 AM
Another possibly hint for combo cuts is to off-set the starting center V-cut for the combo towards one side or the other.  For some, that can make a difference in the sound quality. 
Title: Re: Combo Cut advice needed....
Post by: DUCKDIGGLER on April 29, 2020, 12:47:57 PM
Gobblenut....thnak you for teh suggestion. I will give that a try sir.
Title: Re: Combo Cut advice needed....
Post by: HILBY72 on April 30, 2020, 12:54:01 PM
I make a reverse combo cut with 2- .003 latex over 1 proph. I have a hand jig that was machined by a friend of mine, it has no gauge on it but side tension is 1/4" and all I do with back tension is a very slight smile. Sounds good to me and the turkeys seem to like it, I also snipped the corner off the wing.
Title: Re: Combo Cut advice needed....
Post by: DUCKDIGGLER on April 30, 2020, 08:14:41 PM
Thank you HLBY.....I'll give that a go. I'm making a few right now. Much appreciated!