OG shop member gallery
OldGobbler
          bullet Forum Board      bullet Pushpin Turkey Call Blog      bullet Advertising Info     

OG Gear Store
PATCHES


Sum Toy
Dave Smith
Wood Haven
North Mountain Gear
North Mountain Gear
turkeys for tomorrow






Author Topic: 2 3/4”  (Read 1697 times)

Offline va wingbone

  • Hero Member
  • ***
  • Posts: 294
2 3/4”
« on: October 14, 2022, 01:17:09 PM »
Has anyone loaded any 2 3/4” 20ga magnum hulls with tss? I’ve found some primed 2 3/4” high brass hulls but every body is out of 3” hulls
"around here, turkey hunting is more like a religion than a pastime.getting close to nature, getting back to where we most belong is something we hold sacred.when we do get to take one home, we do so with reverence"

Offline BandedSpur

  • Hero Member
  • ***
  • Posts: 391
Re: 2 3/4”
« Reply #1 on: October 17, 2022, 07:17:28 AM »
Yes

Offline Dylan730

  • Jr. Member
  • *
  • Posts: 11
Re: 2 3/4”
« Reply #2 on: October 24, 2022, 09:37:20 PM »
What are you trimming your 3” hull length to.  I have checked mine and the loads I got from  , I am trimming mine to 2 3/4”. I was considering buying new 2 3/4” hulls if I can ever find them again. I am roll crimping.
« Last Edit: October 25, 2022, 06:40:18 AM by Dylan730 »

Offline BandedSpur

  • Hero Member
  • ***
  • Posts: 391
Re: 2 3/4”
« Reply #3 on: October 25, 2022, 08:17:18 AM »
Not sure if that question was directed at me or the OP. I am loading 2&3/4" hulls with 1&5/8 oz TSS. I trim after everything is in the hull to have 1/4" of hull above the OSC for roll crimping. I am trimming off about 1/16" of hull.

Offline Terry

  • 2024 SITE SUPPORTER
  • Paintbrush Beard
  • ********
  • Posts: 3276
Re: 2 3/4”
« Reply #4 on: October 26, 2022, 05:04:12 PM »
What are you trimming your 3” hull length to.  I have checked mine and the loads I got from  , I am trimming mine to 2 3/4”. I was considering buying new 2 3/4” hulls if I can ever find them again. I am roll crimping.
That is an interesting question…


Sent from my iPhone using Tapatalk

Offline Dylan730

  • Jr. Member
  • *
  • Posts: 11
Re: 2 3/4”
« Reply #5 on: October 26, 2022, 07:56:51 PM »
The question was for either of you,I am loading 1 5/8 oz of #9 tss also.  I have been trimming my 3” hulls to a little short of 2 3/4”. I am using a load recipe from one of the tss suppliers and it calls for a 3” hull, but since I am basically trimming to 2 3/4”, I am considering just buying 2 3/4” hulls. 

Offline BandedSpur

  • Hero Member
  • ***
  • Posts: 391
Re: 2 3/4”
« Reply #6 on: October 27, 2022, 05:42:22 AM »
The question was for either of you,I am loading 1 5/8 oz of #9 tss also.  I have been trimming my 3” hulls to a little short of 2 3/4”. I am using a load recipe from one of the tss suppliers and it calls for a 3” hull, but since I am basically trimming to 2 3/4”, I am considering just buying 2 3/4” hulls.

Should work just fine, provided the primer is the same for the 3" and 2&3/4" hulls that you are using, since you are ending up shorter than 2&3/4" after trimming.

Online crow

  • Double Beard
  • *****
  • Posts: 2935
Re: 2 3/4”
« Reply #7 on: January 27, 2023, 02:26:03 PM »
Has anyone loaded any 2 3/4” 20ga magnum hulls with tss? I’ve found some primed 2 3/4” high brass hulls but every body is out of 3” hulls


yes, great patterns, Hal has load recipes for 2.75"

Offline Reloader

  • Limbhanger
  • ******
  • Posts: 4894
Re: 2 3/4”
« Reply #8 on: February 16, 2023, 09:10:04 AM »
I have quite a few loads that will work in 2-3/4.

Offline Spurs Up

  • Hero Member
  • ***
  • Posts: 467
Re: 2 3/4”
« Reply #9 on: March 12, 2023, 06:45:36 PM »
I have quite a few loads that will work in 2-3/4.

Yes you do!  They “work” alright. Yours are some of my favorites!